 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Rev. 04 -- 9 May 2006 Product data sheet 1. General description The 74HC4053; 74HCT4053 is a high-speed Si-gate CMOS device and is pin compatible with the HEF4053B. It is specified in compliance with JEDEC standard no. 7A. The 74HC4053; 74HCT4053 is triple 2-channel analog multiplexer/demultiplexer with a common enable input (E). Each multiplexer/demultiplexer has two independent inputs/outputs (nY0 and nY1), a common input/output (nZ) and three digital select inputs (Sn). With E LOW, one of the two switches is selected (low-impedance ON-state) by S1 to S3. With E HIGH, all switches are in the high-impedance OFF-state, independent of S1 to S3. VCC and GND are the supply voltage pins for the digital control inputs (S1 to S3 and E). The VCC to GND ranges are 2.0 V to 10.0 V for 74HC4053 and 4.5 V to 5.5 V for 74HCT4053. The analog inputs/outputs (nY0 and nY1, and nZ) can swing between VCC as a positive limit and VEE as a negative limit. VCC - VEE may not exceed 10.0 V. For operation as a digital multiplexer/demultiplexer, VEE is connected to GND (typically ground). 2. Features s Low ON resistance: x 80 (typical) at VCC - VEE = 4.5 V x 70 (typical) at VCC - VEE = 6.0 V x 60 (typical) at VCC - VEE = 9.0 V s Logic level translation: x To enable 5 V logic to communicate with 5 V analog signals s Typical `break before make' built in s Complies with JEDEC standard no. 7A s ESD protection: x HBM EIA/JESD22-A114-C exceeds 2000 V x MM EIA/JESD22-A115-A exceeds 200 V s Multiple package options s Specified from -40 C to +85 C and from -40 C to +125 C Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer 3. Applications s Analog multiplexing and demultiplexing s Digital multiplexing and demultiplexing s Signal gating 4. Quick reference data Table 1: Quick reference data VEE = GND = 0 V; Tamb = 25 C; tr = tf = 6 ns. Symbol Parameter 74HC4053 tPZH, tPZL turn-ON time E to Vos Sn to Vos tPHZ, tPLZ turn-OFF time E to Vos Sn to Vos Ci CS input capacitance switch capacitance independent I/O (nYn) common I/O (nZ) CPD power dissipation capacitance turn-ON time E to Vos Sn to Vos tPHZ, tPLZ turn-OFF time E to Vos Sn to Vos Ci CS input capacitance switch capacitance independent I/O (nYn) common I/O(nZ) CPD [1] Conditions CL = 15 pF; RL = 1 k; VCC = 5 V Min Typ Max Unit CL = 15 pF; RL = 1 k; VCC = 5 V per switch; VI = GND to VCC CL = 15 pF; RL = 1 k; VCC = 5 V CL = 15 pF; RL = 1 k; VCC = 5 V per switch; VI = GND to (VCC - 1.5 V) [1] [1] 17 21 - ns ns 18 17 3.5 5 8 36 - ns ns pF pF pF pF - 74HCT4053 tPZH, tPZL 23 21 - ns ns 20 19 3.5 5 8 36 - ns ns pF pF pF pF power dissipation capacitance - CPD is used to determine the dynamic power dissipation (PD in W). PD = CPD x VCC2 x fi + {(CL + CS) x VCC2 x fo} where: fi = input frequency in MHz; fo = output frequency in MHz; {(CL + CS) x VCC2 x fo} = sum of outputs; (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. 74HC_HCT4053_4 Product data sheet Rev. 04 -- 9 May 2006 2 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer CL = output load capacitance in pF; CS = maximum switch capacitance in pF; VCC = supply voltage in V. 5. Ordering information Table 2: Ordering information Package Temperature range Name 74HC4053 74HC4053N 74HC4053D 74HC4053DB 74HC4053PW 74HC4053BQ -40 C to +125 C -40 C to +125 C -40 C to +125 C -40 C to +125 C -40 C to +125 C DIP16 SO16 SSOP16 TSSOP16 plastic dual in-line package; 16 leads (300 mil); long body plastic small outline package; 16 leads; body width 3.9 mm plastic shrink small outline package; 16 leads; body width 5.3 mm plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT38-4 SOT109-1 SOT338-1 SOT403-1 SOT763-1 Description Version Type number DHVQFN16 plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 16 terminals; body 2.5 x 3.5 x 0.85 mm DIP16 SO16 SSOP16 TSSOP16 plastic dual in-line package; 16 leads (300 mil); long body plastic small outline package; 16 leads; body width 3.9 mm plastic shrink small outline package; 16 leads; body width 5.3 mm plastic thin shrink small outline package; 16 leads; body width 4.4 mm 74HCT4053 74HCT4053N 74HCT4053D -40 C to +125 C -40 C to +125 C SOT38-4 SOT109-1 SOT338-1 SOT403-1 SOT763-1 74HCT4053DB -40 C to +125 C 74HCT4053PW -40 C to +125 C 74HCT4053BQ -40 C to +125 C DHVQFN16 plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 16 terminals; body 2.5 x 3.5 x 0.85 mm 74HC_HCT4053_4 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 3 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer 6. Functional diagram E 6 VCC 16 13 1Y1 S1 11 LOGIC LEVEL CONVERSION DECODER 12 1Y0 14 1Z 1 2Y1 S2 10 2 2Y0 15 2Z 3 3Y1 S3 9 5 3Y0 4 3Z 8 GND 7 VEE 001aae124 Fig 1. Functional diagram 6 11 10 9 S1 S2 S3 1Y0 1Y1 1Z 2Y0 2Y1 2Z 3Y0 3Y1 6 E 3Z 12 13 14 2 1 15 5 3 4 10 15 # 11 14 # EN MUX/DMUX 0 x 0 1 0/1 1 12 13 2 1 9 4 # 5 3 001aae126 001aae125 Fig 2. Logic symbol 74HC_HCT4053_4 Fig 3. IEC logic symbol (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 4 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Y VCC VEE VCC VCC VCC from logic VEE Z VEE 001aad544 Fig 4. Schematic diagram (one switch) 7. Pinning information 7.1 Pinning 74HC4053 74HCT4053 terminal 1 index area 16 VCC 15 2Z 14 1Z 13 1Y1 12 1Y0 GND(1) 11 S1 10 S2 8 GND S3 9 2Y1 2 3 4 5 6 7 1 2Y0 16 VCC 15 2Z 14 1Z 13 1Y1 12 1Y0 11 S1 10 S2 9 001aae127 74HC4053 74HCT4053 2Y1 2Y0 3Y1 3Z 3Y0 E VEE GND 1 2 3 4 5 6 7 8 3Y1 3Z 3Y0 E VEE S3 001aae128 Transparent top view (1) The die substrate is attached to this pad using conductive die attach material. It can not be used as supply pin or input. Fig 5. Pin configuration DIP16, SO16 and (T)SSOP16 Fig 6. Pin configuration DHVQFN16 74HC_HCT4053_4 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 5 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer 7.2 Pin description Table 3: Symbol 2Y1 2Y0 3Y1 3Z 3Y0 E VEE GND S3 S2 S1 1Y0 1Y1 1Z 2Z VCC Pin description Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Description 2 independent input/output 1 2 independent input/output 0 3 independent input/output 1 3 common input/output 3 independent input/output 0 enable input (active LOW) negative supply voltage ground (0 V) select input 3 select input 2 select input 1 1 independent input/output 0 1 independent input/output 1 1 common input/output 2 common input/output supply voltage 8. Functional description 8.1 Function table Table 4: Control E L H [1] H = HIGH voltage level; L = LOW voltage level; X = don't care. Function table [1] Channel on Sn L H X nY0 to nZ nY1 to nZ none 9. Limiting values Table 5: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to VEE = GND (ground = 0 V). [1] Symbol Parameter VCC IIK ISK 74HC_HCT4053_4 Conditions VI < -0.5 V or VI > VCC + 0.5 V VS < -0.5 V or VS > VCC + 0.5 V Min -0.5 - Max +11.0 20 20 Unit V mA mA supply voltage input clamping current switch clamping current (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 6 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Table 5: Limiting values ...continued In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to VEE = GND (ground = 0 V). [1] Symbol Parameter IS IEE ICC IGND Tstg Ptot switch current negative supply current quiescent supply current ground current storage temperature total power dissipation DIP16 package SO16 package SSOP16 package TSSOP16 package DHVQFN16 package PS power dissipation per switch Tamb = -40 C to + 125 C [2] [3] [4] [4] [5] Conditions -0.5 V < VS < VCC + 0.5 V Min -65 - Max 25 -20 50 -50 +150 750 500 500 500 500 100 Unit mA mA mA mA C mW mW mW mW mW mW [1] To avoid drawing VCC current out of terminals nZ, when switch current flows in terminals nYn, the voltage drop across the bidirectional switch must not exceed 0.4 V. If the switch current flows into terminals nZ, no VCC current will flow out of terminals nYn. In this case there is no limit for the voltage drop across the switch, but the voltages at nYn and nZ may not exceed VCC or VEE. For DIP16 package: Ptot derates linearly with 12 mW/K above 70 C. For SO16 package: Ptot derates linearly with 8 mW/K above 70 C. For SSOP16 and TSSOP16 packages: Ptot derates linearly with 5.5 mW/K above 60 C. For DHVQFN16 packages: Ptot derates linearly with 4.5 mW/K above 60 C. [2] [3] [4] [5] 10. Recommended operating conditions Table 6: Symbol 74HC4053 VCC supply voltage difference VCC - GND VCC - VEE VI VS Tamb tr, tf input voltage switch voltage ambient temperature input rise and fall times VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V VCC = 10.0 V 74HCT4053 VCC supply voltage difference VCC - GND VCC - VEE 74HC_HCT4053_4 Recommended operating conditions Parameter Conditions see Figure 7 2.0 2.0 GND VEE -40 5.0 5.0 +25 6.0 6.0 6.0 6.0 10.0 10.0 VCC VCC +125 1000 500 400 250 V V V V C ns ns ns ns Min Typ Max Unit see Figure 7 4.5 2.0 5.0 5.0 5.5 10.0 V V (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 7 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Recommended operating conditions ...continued Parameter input voltage switch voltage ambient temperature input rise and fall times VCC = 4.5 V Conditions Min GND VEE -40 Typ +25 6.0 Max VCC VCC +125 500 Unit V V C ns Table 6: Symbol VI VS Tamb tr, tf 10 VCC - GND (V) 8 001aad545 10 VCC - GND (V) 8 001aad546 6 operating area 6 operating area 4 4 2 2 0 0 2 4 6 8 10 VCC - VEE (V) 0 0 2 4 6 8 10 VCC - VEE (V) a. Type 74HC4053 b. Type 74HCT4053 Fig 7. Guaranteed operating area as a function of the supply voltages 11. Static characteristics Table 7: RON resistance per switch 74HC4053 and 74HCT4053 For test circuit see Figure 8. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. 74HC4053 supply voltages: VCC - GND or VCC - VEE = 2.0 V, 4.5 V, 6.0 V and 9.0 V. 74HCT4053 supply voltages: VCC - GND = 4.5 V or 5.5 V; VCC - VEE = 2.0 V, 4.5 V, 6.0 V and 9.0 V. Symbol RON(peak) Parameter ON resistance (peak) Conditions Vis = VCC to VEE; VI = VIH or VIL VCC = 2.0 V; VEE = 0 V; IS = 100 A VCC = 4.5 V; VEE = 0 V; IS = 1000 A VCC = 6.0 V; VEE = 0 V; IS = 1000 A VCC = 4.5 V; VEE = -4.5 V; IS = 1000 A [1] Min Typ Max Unit Tamb = 25 C 100 90 70 180 160 130 74HC_HCT4053_4 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 8 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Table 7: RON resistance per switch 74HC4053 and 74HCT4053 ...continued For test circuit see Figure 8. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. 74HC4053 supply voltages: VCC - GND or VCC - VEE = 2.0 V, 4.5 V, 6.0 V and 9.0 V. 74HCT4053 supply voltages: VCC - GND = 4.5 V or 5.5 V; VCC - VEE = 2.0 V, 4.5 V, 6.0 V and 9.0 V. Symbol RON(rail) Parameter ON resistance (rail) Conditions Vis = VEE; VI = VIH or VIL VCC = 2.0 V; VEE = 0 V; IS = 100 A VCC = 4.5 V; VEE = 0 V; IS = 1000 A VCC = 6.0 V; VEE = 0 V; IS = 1000 A VCC = 4.5 V; VEE = -4.5 V; IS = 1000 A Vis = VCC; VI = VIH or VIL VCC = 2.0 V; VEE = 0 V; IS = 100 A VCC = 4.5 V; VEE = 0 V; IS = 1000 A VCC = 6.0 V; VEE = 0 V; IS = 1000 A VCC = 4.5 V; VEE = -4.5 V; IS = 1000 A RON ON resistance mismatch between channels Vis = VCC to VEE; VI = VIH or VIL VCC = 2.0 V; VEE = 0 V VCC = 4.5 V; VEE = 0 V VCC = 6.0 V; VEE = 0 V VCC = 4.5 V; VEE = -4.5 V Tamb = -40 C to +85 C RON(peak) ON resistance (peak) Vis = VCC to VEE; VI = VIH or VIL VCC = 2.0 V; VEE = 0 V; IS = 100 A VCC = 4.5 V; VEE = 0 V; IS = 1000 A VCC = 6.0 V; VEE = 0 V; IS = 1000 A VCC = 4.5 V; VEE = -4.5 V; IS = 1000 A RON(rail) ON resistance (rail) Vis = VEE; VI = VIH or VIL VCC = 2.0 V; VEE = 0 V; IS = 100 A VCC = 4.5 V; VEE = 0 V; IS = 1000 A VCC = 6.0 V; VEE = 0 V; IS = 1000 A VCC = 4.5 V; VEE = -4.5 V; IS = 1000 A Vis = VCC; VI = VIH or VIL VCC = 2.0 V; VEE = 0 V; IS = 100 A VCC = 4.5 V; VEE = 0 V; IS = 1000 A VCC = 6.0 V; VEE = 0 V; IS= 1000 A VCC = 4.5 V; VEE = -4.5 V; IS = 1000 A Tamb = -40 C to +125 C RON(peak) ON resistance (peak) Vis = VCC to VEE; VI = VIH or VIL VCC = 2.0 V; VEE = 0 V; IS = 100 A VCC = 4.5 V; VEE = 0 V; IS = 1000 A VCC = 6.0 V; VEE = 0 V; IS = 1000 A VCC = 4.5 V; VEE = -4.5 V; IS = 1000 A 74HC_HCT4053_4 Min [1] Typ 150 80 70 60 150 90 80 65 9 8 6 Max 140 120 105 160 140 120 - Unit - [1] - [1] - [1] - - 225 200 165 175 150 130 200 175 150 [1] - [1] - [1] - - 270 240 195 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 9 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Table 7: RON resistance per switch 74HC4053 and 74HCT4053 ...continued For test circuit see Figure 8. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. 74HC4053 supply voltages: VCC - GND or VCC - VEE = 2.0 V, 4.5 V, 6.0 V and 9.0 V. 74HCT4053 supply voltages: VCC - GND = 4.5 V or 5.5 V; VCC - VEE = 2.0 V, 4.5 V, 6.0 V and 9.0 V. Symbol RON(rail) Parameter ON resistance (rail) Conditions Vis = VEE; VI = VIH or VIL VCC = 2.0 V; VEE = 0 V; IS = 100 A VCC = 4.5 V; VEE = 0 V; IS = 1000 A VCC = 6.0 V; VEE = 0 V; IS = 1000 A VCC = 4.5 V; VEE = -4.5 V; IS = 1000 A Vis = VCC; VI = VIH or VIL VCC = 2.0 V; VEE = 0 V; IS = 100 A VCC = 4.5 V; VEE = 0 V; IS = 1000 A VCC = 6.0 V; VEE = 0 V; IS = 1000 A VCC = 4.5 V; VEE = -4.5 V; IS = 1000 A [1] [1] [1] Min - Typ - Max 210 180 160 240 210 180 Unit At supply voltages (VCC - VEE) approaching 2.0 V the analog switch ON resistance becomes extremely non-linear. Therefore, it is recommended that these devices be used to transmit digital signals only, when using these supply voltages. 110 RON () 90 HIGH (from select input) (1) mnb047 VS nYn nZ 70 (2) 50 Vis = 0 V to (VCC - VEE) IS (3) VEE 001aae129 30 10 0 1.8 3.6 5.4 7.2 Vis (V) 9.0 RON = VS / IS. Vis = 0 V to (VCC - VEE). (1) VCC = 4.5 V (2) VCC = 6 V (3) VCC = 9 V Fig 8. Test circuit for measuring RON Fig 9. Typical RON as a function of input voltage Vis 74HC_HCT4053_4 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 10 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Table 8: Static characteristics 74HC4053 At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol VIH Parameter Conditions Min 1.5 3.15 4.2 6.3 Typ 1.2 2.4 3.2 4.7 0.8 2.1 2.8 4.3 Max 0.5 1.35 1.8 2.7 0.1 0.2 Unit V V V V V V V V A A Tamb = 25 C HIGH-state input voltage VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V VCC = 9.0 V VIL LOW-state input voltage VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V VCC = 9.0 V ILI input leakage current VI = VCC or GND; VEE = 0 V VCC = 6.0 V VCC = 10.0 V IS(OFF) OFF-state leakage current VCC = 10.0 V; VI = VIH or VIL; VEE = 0 V; |VS| = VCC - VEE; see Figure 10 per channel all channels IS(ON) ICC ON-state leakage current VCC = 10.0 V; VI = VIH or VIL; VEE = 0 V; |VS| = VCC - VEE; see Figure 11 0.1 0.1 0.1 A A A quiescent supply current Vis = VEE or VCC; Vos = VCC or VEE; VI = VCC or GND; VEE = 0 V VCC = 6.0 V VCC = 10.0 V 1.5 3.15 4.2 6.3 3.5 5 8 8.0 16.0 0.5 1.35 1.8 2.7 1.0 2.0 A A pF pF pF V V V V V V V V A A Ci CS input capacitance switch capacitance independent I/O (nYn) common I/O (nZ) Tamb = -40 C to +85 C VIH HIGH-state input voltage VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V VCC = 9.0 V VIL LOW-state input voltage VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V VCC = 9.0 V ILI input leakage current VI = VCC or GND; VEE = 0 V VCC = 6.0 V VCC = 10.0 V 74HC_HCT4053_4 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 11 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Table 8: Static characteristics 74HC4053 ...continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol IS(OFF) Parameter OFF-state leakage current Conditions VCC = 10.0 V; VI = VIH or VIL; VEE = 0 V; |VS| = VCC - VEE; see Figure 10 per channel all channels IS(ON) ICC ON-state leakage current VCC = 10.0 V; VI = VIH or VIL; VEE = 0 V; |VS| = VCC - VEE; see Figure 11 1.0 1.0 1.0 A A A Min Typ Max Unit quiescent supply current Vis = VEE or VCC; Vos = VCC or VEE; VI = VCC or GND; VEE = 0 V VCC = 6.0 V VCC = 10.0 V 1.5 3.15 4.2 6.3 80.0 160.0 0.5 1.35 1.8 2.7 1.0 2.0 A A V V V V V V V V A A Tamb = -40 C to +125 C VIH HIGH-state input voltage VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V VCC = 9.0 V VIL LOW-state input voltage VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V VCC = 9.0 V ILI input leakage current VI = VCC or GND; VEE = 0 V VCC = 6.0 V VCC = 10.0 V IS(OFF) OFF-state leakage current VCC = 10.0 V; VI = VIH or VIL; VEE = 0 V; |VS| = VCC - VEE; see Figure 10 per channel all channels IS(ON) ICC ON-state leakage current VCC = 10.0 V; VI = VIH or VIL; VEE = 0 V; |VS| = VCC - VEE; see Figure 11 1.0 1.0 1.0 A A A quiescent supply current Vis = VEE or VCC; Vos = VCC or VEE; VI = VCC or GND; VEE = 0 V VCC = 6.0 V VCC = 10.0 V 160.0 320.0 A A Table 9: Static characteristics 74HCT4053 Voltages are referenced to GND (ground = 0 V). Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol VIH VIL 74HC_HCT4053_4 Parameter Conditions Min 2.0 - Typ 1.6 1.2 Max 0.8 Unit A A Tamb = 25 C HIGH-state input voltage VCC = 4.5 V to 5.5 V LOW-state input voltage VCC = 4.5 V to 5.5 V (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 12 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Table 9: Static characteristics 74HCT4053 ...continued Voltages are referenced to GND (ground = 0 V). Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol ILI IS(OFF) Parameter input leakage current OFF-state leakage current Conditions VCC = 5.5 V; VEE = 0 V; VI = VCC or GND VCC = 10.0 V; VI = VIH or VIL; VEE = 0 V; |VS| = VCC - VEE; see Figure 10 per channel all channels IS(ON) ICC ON-state leakage current VCC = 10.0 V; VI = VIH or VIL; VEE = 0 V; |VS| = VCC - VEE; see Figure 11 0.1 0.1 0.1 A A A Min Typ Max 0.1 Unit A quiescent supply current VI = VCC or GND; Vis = VEE or VCC; Vos = VCC or VEE VCC = 5.5 V; VEE = 0 V VCC = 5.0 V; VEE = -5.0 V 50 8.0 16.0 180 A A A ICC additional quiescent supply current input capacitance switch capacitance independent I/O (nYn) common I/O (nZ) per input pin; VCC = 4.5 V to 5.5 V; VEE = 0 V; VI = VCC - 2.1 V; other inputs at VCC or GND Ci CS 2.0 - 3.5 5 8 - 0.8 1.0 pF pF pF A A A Tamb = -40 C to +85 C VIH VIL ILI IS(OFF) HIGH-state input voltage VCC = 4.5 V to 5.5 V LOW-state input voltage input leakage current OFF-state leakage current VCC = 4.5 V to 5.5 V VCC = 5.5 V; VEE = 0 V; VI = VCC or GND VCC = 10.0 V; VI = VIH or VIL; VEE = 0 V; |VS| = VCC - VEE; see Figure 10 per channel all channels IS(ON) ICC ON-state leakage current VCC = 10.0 V; VI = VIH or VIL; VEE = 0 V; |VS| = VCC - VEE; see Figure 11 1.0 1.0 1.0 A A A quiescent supply current VI = VCC or GND; Vis = VEE or VCC; Vos = VCC or VEE VCC = 5.5 V; VEE = 0 V VCC = 5.0 V; VEE = -5.0 V 80.0 160.0 225 A A A ICC additional quiescent supply current per input pin; VCC = 4.5 V to 5.5 V; VEE = 0 V; VI = VCC - 2.1 V; other inputs at VCC or GND Tamb = -40 C to +125 C VIH VIL ILI HIGH-state input voltage VCC = 4.5 V to 5.5 V LOW-state input voltage input leakage current VCC = 4.5 V to 5.5 V VCC = 5.5 V; VEE = 0 V; VI = VCC or GND 2.0 0.8 1.0 A A A 74HC_HCT4053_4 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 13 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Table 9: Static characteristics 74HCT4053 ...continued Voltages are referenced to GND (ground = 0 V). Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol IS(OFF) Parameter OFF-state leakage current Conditions VCC = 10.0 V; VI = VIH or VIL; VEE = 0 V; |VS| = VCC - VEE; see Figure 10 per channel all channels IS(ON) ICC ON-state leakage current VCC = 10.0 V; VI = VIH or VIL; VEE = 0 V; |VS| = VCC - VEE; see Figure 11 1.0 1.0 1.0 A A A Min Typ Max Unit quiescent supply current VI = VCC or GND; Vis = VEE or VCC; Vos = VCC or VEE VCC = 5.5 V; VEE = 0 V VCC = 5.0 V; VEE = -5.0 V 160.0 320.0 245 A A A ICC additional quiescent supply current per input pin; VCC = 4.5 V to 5.5 V; VEE = 0 V; VI = VCC - 2.1 V; other inputs at VCC or GND LOW (select input) Sn HIGH (select input) Sn nYn A VI = VCC or VEE nZ A VO = VEE or VCC VEE 001aae130 nYn A VI = VEE or VCC nZ VO (open circuit) VEE 001aae131 Fig 10. Test circuit for measuring OFF-state leakage current Fig 11. Test circuit for measuring ON-state leakage current 12. Dynamic characteristics Table 10: Dynamic characteristics type 74HC4053 Voltages are referenced to GND (ground = 0 V); tr = tf = 6 ns; CL = 50 pF unless otherwise specified; for test circuit see Figure 14. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol Parameter Tamb = 25 C tPHL, tPLH propagation delay Vis to Vos RL = ; see Figure 12 VCC = 2.0 V; VEE = 0 V VCC = 4.5 V; VEE = 0 V VCC = 6.0 V; VEE = 0 V VCC = 4.5 V; VEE = -4.5 V 15 5 4 4 60 12 10 8 ns ns ns ns Conditions Min Typ Max Unit 74HC_HCT4053_4 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 14 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Table 10: Dynamic characteristics type 74HC4053 ...continued Voltages are referenced to GND (ground = 0 V); tr = tf = 6 ns; CL = 50 pF unless otherwise specified; for test circuit see Figure 14. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol Parameter tPZH, tPZL turn-ON time E to Vos Conditions RL = 1 k; see Figure 13 VCC = 2.0 V; VEE = 0 V VCC = 4.5 V; VEE = 0 V VCC = 6.0 V; VEE = 0 V VCC = 4.5 V; VEE = -4.5 V VCC = 5 V; VEE = 0 V; CL = 15 pF Sn to Vos VCC = 2.0 V; VEE = 0 V VCC = 4.5 V; VEE = 0 V VCC = 6.0 V; VEE = 0 V VCC = 4.5 V; VEE = -4.5 V VCC = 5 V; VEE = 0 V; CL = 15 pF tPHZ, tPLZ turn-OFF time E to Vos RL = 1 k; see Figure 13 VCC = 2.0 V; VEE = 0 V VCC = 4.5 V; VEE = 0 V VCC = 6.0 V; VEE = 0 V VCC = 4.5 V; VEE = -4.5 V VCC = 5 V; CL = 15 pF Sn to Vos VCC = 2.0 V; VEE = 0 V VCC = 4.5 V; VEE = 0 V VCC = 6.0 V; VEE = 0 V VCC = 4.5 V; VEE = -4.5 V VCC = 5 V; CL = 15 pF CPD power dissipation capacitance propagation delay Vis to Vos per switch; VI = GND to VCC [1] Min - Typ 60 20 16 15 17 75 25 20 15 21 63 21 17 15 18 60 20 16 15 17 36 Max 220 44 37 31 220 44 37 31 210 42 36 29 210 42 36 29 - Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns pF Tamb = -40 C to +85 C tPHL, tPLH RL = ; see Figure 12 VCC = 2.0 V; VEE = 0 V VCC = 4.5 V; VEE = 0 V VCC = 6.0 V; VEE = 0 V VCC = 4.5 V; VEE = -4.5 V 75 15 13 10 ns ns ns ns 74HC_HCT4053_4 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 15 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Table 10: Dynamic characteristics type 74HC4053 ...continued Voltages are referenced to GND (ground = 0 V); tr = tf = 6 ns; CL = 50 pF unless otherwise specified; for test circuit see Figure 14. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol Parameter tPZH, tPZL turn-ON time E to Vos Conditions RL = 1 k; see Figure 13 VCC = 2.0 V; VEE = 0 V VCC = 4.5 V; VEE = 0 V VCC = 6.0 V; VEE = 0 V VCC = 4.5 V; VEE = -4.5 V Sn to Vos VCC = 2.0 V; VEE = 0 V VCC = 4.5 V; VEE = 0 V VCC = 6.0 V; VEE = 0 V VCC = 4.5 V; VEE = -4.5 V tPHZ, tPLZ turn-OFF time E to Vos RL = 1 k; see Figure 13 VCC = 2.0 V; VEE = 0 V VCC = 4.5 V; VEE = 0 V VCC = 6.0 V; VEE = 0 V VCC = 4.5 V; VEE = -4.5 V Sn to Vos VCC = 2.0 V; VEE = 0 V VCC = 4.5 V; VEE = 0 V VCC = 6.0 V; VEE = 0 V VCC = 4.5 V; VEE = -4.5 V Tamb = -40 C to +125 C tPHL, tPLH propagation delay Vis to Vos RL = ; see Figure 12 VCC = 2.0 V; VEE = 0 V VCC = 4.5 V; VEE = 0 V VCC = 6.0 V; VEE = 0 V VCC = 4.5 V; VEE = -4.5 V tPZH, tPZL turn-ON time E to Vos RL = 1 k; see Figure 13 VCC = 2.0 V; VEE = 0 V VCC = 4.5 V; VEE = 0 V VCC = 6.0 V; VEE = 0 V VCC = 4.5 V; VEE = -4.5 V Sn to Vos VCC = 2.0 V; VEE = 0 V VCC = 4.5 V; VEE = 0 V VCC = 6.0 V; VEE = 0 V VCC = 4.5 V; VEE = -4.5 V 330 66 56 47 330 66 56 47 ns ns ns ns ns ns ns ns 90 18 15 12 ns ns ns ns 265 53 45 36 265 53 45 36 ns ns ns ns ns ns ns ns 275 55 47 39 275 55 47 39 ns ns ns ns ns ns ns ns Min Typ Max Unit 74HC_HCT4053_4 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 16 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Table 10: Dynamic characteristics type 74HC4053 ...continued Voltages are referenced to GND (ground = 0 V); tr = tf = 6 ns; CL = 50 pF unless otherwise specified; for test circuit see Figure 14. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol Parameter tPHZ, tPLZ turn-OFF time E to Vos Conditions RL = 1 k; see Figure 13 VCC = 2.0 V; VEE = 0 V VCC = 4.5 V; VEE = 0 V VCC = 6.0 V; VEE = 0 V VCC = 4.5 V; VEE = -4.5 V Sn to Vos VCC = 2.0 V; VEE = 0 V VCC = 4.5 V; VEE = 0 V VCC = 6.0 V; VEE = 0 V VCC = 4.5 V; VEE = -4.5 V [1] CPD is used to determine the dynamic power dissipation (PD in W): PD = CPD x VCC2 x fi + {(CL + CS) x VCC2 x fo} where: fi = input frequency in MHz; fo = output frequency in MHz; {(CL + CS) x VCC2 x fo} = sum of outputs; CL = output load capacitance in pF; CS = maximum switch capacitance in pF; VCC = supply voltage in V. Min - Typ - Max 315 63 54 44 315 63 54 44 Unit ns ns ns ns ns ns ns ns Table 11: Dynamic characteristics type 74HCT4053 Voltages are referenced to GND (ground = 0 V); tr = tf = 6 ns; CL = 50 pF unless otherwise specified; for test circuit see Figure 14. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol Parameter Tamb = 25 C tPHL, tPLH propagation delay Vis to Vos VCC = 4.5 V; RL = ; see Figure 12 VEE = 0 V VEE = -4.5 V tPZH, tPZL turn-ON time E to Vos RL = 1 k; see Figure 13 VCC = 4.5 V; VEE = 0 V VCC = 4.5 V; VEE = -4.5 V VCC = 5 V; VEE = 0 V; CL = 15 pF Sn to Vos VCC = 4.5 V; VEE = 0 V VCC = 4.5 V; VEE = -4.5 V VCC = 5 V; VEE = 0 V; CL = 15 pF 27 16 23 25 16 21 48 34 48 34 ns ns ns ns ns ns 5 4 12 8 ns ns Conditions Min Typ Max Unit 74HC_HCT4053_4 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 17 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Table 11: Dynamic characteristics type 74HCT4053 ...continued Voltages are referenced to GND (ground = 0 V); tr = tf = 6 ns; CL = 50 pF unless otherwise specified; for test circuit see Figure 14. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol Parameter tPHZ, tPLZ turn-OFF time E to Vos Conditions RL = 1 k; see Figure 13 VCC = 4.5 V; VEE = 0 V VCC = 4.5 V; VEE = -4.5 V VCC = 5 V; VEE = 0 V; CL = 15 pF Sn to Vos VCC = 4.5 V; VEE = 0 V VCC = 4.5 V; VEE = -4.5 V VCC = 5 V; VEE = 0 V; CL = 15 pF CPD power dissipation capacitance propagation delay Vis to Vos per switch; VI = GND to (VCC - 1.5 V) [1] Min - Typ 24 15 20 22 15 19 36 Max 44 31 44 31 - Unit ns ns ns ns ns ns pF Tamb = -40 C to +85 C tPHL, tPLH VCC = 4.5 V; RL = ; see Figure 12 VEE = 0 V VEE = -4.5 V tPZH, tPZL turn-ON time E to Vos Sn to Vos tPHZ, tPLZ turn-OFF time E to Vos Sn to Vos Tamb = -40 C to +125 C tPHL, tPLH propagation delay Vis to Vos VCC = 4.5 V; RL = ; see Figure 12 VEE = 0 V VEE = -4.5 V tPZH, tPZL turn-ON time E to Vos Sn to Vos VCC = 4.5 V; RL = 1 k; see Figure 13 VEE = 0 V VEE = -4.5 V VEE = 0 V VEE = -4.5 V 72 51 72 51 ns ns ns ns 18 12 ns ns VCC = 4.5 V; RL = 1 k; see Figure 13 VEE = 0 V VEE = -4.5 V VEE = 0 V VEE = -4.5 V VCC = 4.5 V; RL = 1 k; see Figure 13 VEE = 0 V VEE = -4.5 V VEE = 0 V VEE = -4.5 V 55 39 55 39 ns ns ns ns 60 43 60 43 ns ns ns ns 15 10 ns ns 74HC_HCT4053_4 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 18 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Table 11: Dynamic characteristics type 74HCT4053 ...continued Voltages are referenced to GND (ground = 0 V); tr = tf = 6 ns; CL = 50 pF unless otherwise specified; for test circuit see Figure 14. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol Parameter tPHZ, tPLZ turn-OFF time E to Vos Sn to Vos Conditions VCC = 4.5 V; RL = 1 k; see Figure 13 VEE = 0 V VEE = -4.5 V VEE = 0 V VEE = -4.5 V [1] CPD is used to determine the dynamic power dissipation (PD in W): PD = CPD x VCC2 x fi + {(CL + CS) x VCC2 x fo} where: fi = input frequency in MHz; fo = output frequency in MHz; {(CL + CS) x VCC2 x fo} = sum of outputs; CL = output load capacitance in pF; CS = maximum switch capacitance in pF; VCC = supply voltage in V. Min - Typ - Max 66 47 66 47 Unit ns ns ns ns 13. Waveforms Vis input 50 % tPLH tPHL Vos output 50 % 001aad555 Fig 12. Propagation delay input (Vis) to output (Vos) 74HC_HCT4053_4 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 19 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer VI E, Sn inputs 0V tPLZ VM tPZL Vos output 10 % tPHZ 90 % Vos output tPZH 50 % 50 % switch ON switch OFF switch ON 001aae330 (1) Measurement points are given in Table 12. Fig 13. Turn-ON and turn-OFF times Table 12: Type 74HC4053 74HCT4053 Measurement points Input VM 0.5VCC 1.3 V 74HC_HCT4053_4 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 20 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer VI negative pulse 0V tW 90 % VM 10 % tf tr tr tf 90 % VM 10 % tW VM VM VI positive pulse 0V VCC Vis PULSE GENERATOR VI DUT RT CL VCC Vos RL S1 open GND VEE 001aae382 Test data is given in Table 13. RT = Termination resistance should be equal to output impedance Zo of the pulse generator. CL = Load capacitance including jig and probe capacitance. RL = Load resistor. S1 = Test selection switch. Fig 14. Load circuitry for switching times Table 13: Test Test data Input VI tPHL, tPLH tPZH, tPHZ tPZL, tPLZ [1] [1] [1] [1] Load Vis pulse VCC VEE tr, tf at fmax < 2 ns < 2 ns < 2 ns other 6 ns 6 ns 6 ns 15 pF, 50 pF 15 pF, 50 pF 15 pF, 50 pF 1 k 1 k 1 k CL RL S1 position open VEE VCC VI values: a) For 74HC4053: VI = VCC. b) For 74HCT4053: VI = 3 V. 74HC_HCT4053_4 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 21 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer 14. Additional dynamic characteristics Table 14: Additional dynamic characteristics 74HC4053 and 74HCT4053 GND = 0 V; Tamb = 25 C. Vis is the input voltage at an nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at an nYn or nZ terminal, whichever is assigned as an output. Symbol dsin Parameter sine wave distortion Conditions RL = 10 k; CL = 50 pF; see Figure 15 fi = 1 kHz VCC = 2.25 V; VEE = -2.25 V; Vis = 4.0 V (p-p) VCC = 4.5 V; VEE = -4.5 V; Vis = 8.0 V (p-p) fi = 10 kHz VCC = 2.25 V; VEE = -2.25 V; Vis = 4.0 V (p-p) VCC = 4.5 V; VEE = -4.5 V; Vis = 8.0 V (p-p) (OFF)(ft) OFF-state feed-through attenuation RL = 600 ; CL = 50 pF; fi = 1 MHz; see Figure 16 VCC = 2.25 V; VEE = -2.25 V VCC = 4.5 V; VEE = -4.5 V Vct(sw-sw) crosstalk between switches RL = 600 ; CL = 50 pF; fi = 1 MHz; see Figure 17 VCC = 2.25 V; VEE = -2.25 V VCC = 4.5 V; VEE = -4.5 V Vct(d-sw) crosstalk between digital inputs and switch VCC = 4.5 V; RL = 600 k; CL = 50 pF; fi = 1 MHz; see Figure 18 VEE = 0 V VEE = -4.5 V f(-3dB) -3 dB frequency response RL = 50 ; CL = 10 pF; see Figure 19 VCC = 2.25 V; VEE = -2.25 V VCC = 4.5 V; VEE = -4.5 V [1] [2] [3] Adjust input voltage Vis to 0 dBm level (0 dBm = 1 mW into 600 ). Control input E or Sn, with square-wave between VCC and GND. Adjust input voltage Vis to 0 dBm level at Vos for 1 MHz (0 dBm = 1 mW into 50 ). [3] [2] [1] [1] Min Typ Max Unit - 0.04 0.02 0.12 0.06 - % % % % - -50 -50 - dB dB - -60 -60 - dB dB - 110 220 160 170 - mV mV MHz MHz 10 F Vis nYn or nZ nZ or nYn RL CL dB Vos channel ON GND 001aae132 Fig 15. Test circuit for measuring sine wave distortion 74HC_HCT4053_4 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 22 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer 0 (OFF)(ft) (dB) -20 001aae332 -40 -60 -80 -100 10 102 103 104 105 fi (kHz) 106 a. Feed-through as function of the frequency 0.1 F Vis nYn or nZ nZ or nYn RL CL dB Vos channel OFF GND 001aae133 b. Test circuit Fig 16. Typical switch OFF signal feed-through as a function of frequency 74HC_HCT4053_4 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 23 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer 0.1 F RL Vis nYn or nZ nZ or nYn RL CL dB Vos channel ON GND 001aae134 a. Switch ON Vis nYn or nZ nZ or nYn Vos RL channel OFF RL CL dB GND 001aae259 b. Switch OFF Fig 17. Test circuits for measuring crosstalk between any two switches VCC 2RL Sn or E VCC 2RL Vct(d-sw) nYn or nZ 2RL DUT 2RL CL nZ or nYn oscilloscope GND VEE 001aae135 Fig 18. Test circuit for measuring crosstalk between digital inputs and switch 74HC_HCT4053_4 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 24 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer 5 Vos (dB) 3 001aad551 1 -1 -3 -5 10 102 103 104 105 f (kHz) 106 a. Typical frequency response 10 F Vis nYn or nZ nZ or nYn RL CL dB Vos channel ON GND 001aae132 b. Test circuit Fig 19. Typical frequency response 74HC_HCT4053_4 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 25 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer 15. Package outline DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4 D seating plane ME A2 A L A1 c Z e b1 b 16 9 b2 MH wM (e 1) pin 1 index E 1 8 0 5 scale 10 mm DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT mm inches A max. 4.2 0.17 A1 min. 0.51 0.02 A2 max. 3.2 0.13 b 1.73 1.30 0.068 0.051 b1 0.53 0.38 0.021 0.015 b2 1.25 0.85 0.049 0.033 c 0.36 0.23 0.014 0.009 D (1) 19.50 18.55 0.77 0.73 E (1) 6.48 6.20 0.26 0.24 e 2.54 0.1 e1 7.62 0.3 L 3.60 3.05 0.14 0.12 ME 8.25 7.80 0.32 0.31 MH 10.0 8.3 0.39 0.33 w 0.254 0.01 Z (1) max. 0.76 0.03 Note 1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. OUTLINE VERSION SOT38-4 REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 95-01-14 03-02-13 Fig 20. Package outline SOT38-4 (DIP16) 74HC_HCT4053_4 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 26 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1 D E A X c y HE vMA Z 16 9 Q A2 pin 1 index Lp 1 e bp 8 wM L detail X A1 (A 3) A 0 2.5 scale 5 mm DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT mm inches Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. OUTLINE VERSION SOT109-1 REFERENCES IEC 076E07 JEDEC MS-012 JEITA EUROPEAN PROJECTION A max. 1.75 A1 0.25 0.10 A2 1.45 1.25 A3 0.25 0.01 bp 0.49 0.36 c 0.25 0.19 D (1) 10.0 9.8 E (1) 4.0 3.8 0.16 0.15 e 1.27 0.05 HE 6.2 5.8 L 1.05 Lp 1.0 0.4 0.039 0.016 Q 0.7 0.6 0.028 0.020 v 0.25 0.01 w 0.25 0.01 y 0.1 Z (1) 0.7 0.3 0.010 0.057 0.069 0.004 0.049 0.019 0.0100 0.39 0.014 0.0075 0.38 0.244 0.041 0.228 0.028 0.004 0.012 8 o 0 o ISSUE DATE 99-12-27 03-02-19 Fig 21. Package outline SOT109-1 (SO16) 74HC_HCT4053_4 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 27 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer SSOP16: plastic shrink small outline package; 16 leads; body width 5.3 mm SOT338-1 D E A X c y HE vM A Z 16 9 Q A2 A1 pin 1 index Lp L 1 bp 8 wM detail X (A 3) A e 0 2.5 scale 5 mm DIMENSIONS (mm are the original dimensions) UNIT mm A max. 2 A1 0.21 0.05 A2 1.80 1.65 A3 0.25 bp 0.38 0.25 c 0.20 0.09 D (1) 6.4 6.0 E (1) 5.4 5.2 e 0.65 HE 7.9 7.6 L 1.25 Lp 1.03 0.63 Q 0.9 0.7 v 0.2 w 0.13 y 0.1 Z (1) 1.00 0.55 8 o 0 o Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT338-1 REFERENCES IEC JEDEC MO-150 JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-19 Fig 22. Package outline SOT338-1 (SSOP16) 74HC_HCT4053_4 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 28 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 D E A X c y HE vMA Z 16 9 Q A2 pin 1 index A1 Lp L (A 3) A 1 e bp 8 wM detail X 0 2.5 scale 5 mm DIMENSIONS (mm are the original dimensions) UNIT mm A max. 1.1 A1 0.15 0.05 A2 0.95 0.80 A3 0.25 bp 0.30 0.19 c 0.2 0.1 D (1) 5.1 4.9 E (2) 4.5 4.3 e 0.65 HE 6.6 6.2 L 1 Lp 0.75 0.50 Q 0.4 0.3 v 0.2 w 0.13 y 0.1 Z (1) 0.40 0.06 8 o 0 o Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT403-1 REFERENCES IEC JEDEC MO-153 JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-18 Fig 23. Package outline SOT403-1 (TSSOP16) 74HC_HCT4053_4 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 29 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer DHVQFN16: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; SOT763-1 16 terminals; body 2.5 x 3.5 x 0.85 mm D B A A A1 E c terminal 1 index area detail X terminal 1 index area e 2 L e1 b 7 vMCAB wM C y1 C C y 1 Eh 16 8 e 9 15 Dh 10 X 2.5 scale 5 mm 0 DIMENSIONS (mm are the original dimensions) UNIT mm A(1) max. 1 A1 0.05 0.00 b 0.30 0.18 c 0.2 D (1) 3.6 3.4 Dh 2.15 1.85 E (1) 2.6 2.4 Eh 1.15 0.85 e 0.5 e1 2.5 L 0.5 0.3 v 0.1 w 0.05 y 0.05 y1 0.1 Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. OUTLINE VERSION SOT763-1 REFERENCES IEC --JEDEC MO-241 JEITA --EUROPEAN PROJECTION ISSUE DATE 02-10-17 03-01-27 Fig 24. Package outline SOT763-1 (DHVQFN16) 74HC_HCT4053_4 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 30 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer 16. Abbreviations Table 15: Acronym CMOS HBM ESD MM DUT Abbreviations Description Complementary Metal Oxide Semiconductor Human Body Model ElectroStatic Discharge Machine Model Device Under Test 17. Revision history Table 16: Revision history Release date 20060509 Data sheet status Product data sheet Change notice Doc. number Supersedes 74HC_HCT4053_3 Document ID 74HC_HCT4053_4 Modifications: 74HC_HCT4053_3 Modifications: * Section 5 "Ordering information": errors corrected, type numbers in wrong order and SOT38-4 is the package for types 74HC4053N and 74HCT4053N Product data sheet 74HC_HCT4053_ CNV_2 20060315 * * The format of this data sheet has been redesigned to comply with the new presentation and information standard of Philips Semiconductors. Added type numbers 74HC4053BQ and 74HCT4053BQ (DHVQFN16) package to Section 5 "Ordering information", Section 7 "Pinning information" and Section 15 "Package outline" Product specification - 74HC_HCT4053_CNV_2 19901201 74HC_HCT4053_4 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 31 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer 18. Data sheet status Level I II Data sheet status [1] Objective data Preliminary data Product status [2] [3] Development Qualification Definition This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). III Product data Production [1] [2] [3] Please consult the most recently issued data sheet before initiating or completing a design. The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. 19. Definitions Short-form specification -- The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition -- Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information -- Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes -- Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status `Production'), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. 21. Trademarks Notice -- All referenced brands, product names, service names and trademarks are the property of their respective owners. 20. Disclaimers Life support -- These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors 22. Contact information For additional information, please visit: http://www.semiconductors.philips.com For sales office addresses, send an email to: sales.addresses@www.semiconductors.philips.com 74HC_HCT4053_4 (c) Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 -- 9 May 2006 32 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer 23. Contents 1 2 3 4 5 6 7 7.1 7.2 8 8.1 9 10 11 12 13 14 15 16 17 18 19 20 21 22 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Quick reference data . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 3 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 4 Pinning information . . . . . . . . . . . . . . . . . . . . . . 5 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 6 Functional description . . . . . . . . . . . . . . . . . . . 6 Function table . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 6 Recommended operating conditions. . . . . . . . 7 Static characteristics. . . . . . . . . . . . . . . . . . . . . 8 Dynamic characteristics . . . . . . . . . . . . . . . . . 14 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Additional dynamic characteristics . . . . . . . . 22 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 26 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 31 Data sheet status . . . . . . . . . . . . . . . . . . . . . . . 32 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Contact information . . . . . . . . . . . . . . . . . . . . 32 (c) Koninklijke Philips Electronics N.V. 2006 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 9 May 2006 Document number: 74HC_HCT4053_4 Published in The Netherlands |
Price & Availability of 74HCT4053
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |